CCNA CCNP Cisco Certification Exam Braindumps

46. The network shown in the diagram is experiencing connectivity problems. Which of the following will correct the problems? (Choose two.)

A. Configure the gateway on Host A as 10.1.1.1.

B. Configure the gateway on Host B as 10.1.2.254.

C. Configure the IP address of Host A as 10.1.2.2.

D. Configure the IP address of Host B as 10.1.2.2.

E. Configure the masks on both hosts to be 255.255.255.224.

F. Configure the masks on both hosts to be 255.255.255.240.

Answer: BD

47. Which three statements are correct about RIP version 2? (Choose three.)

A. It has the same maximum hop count as version 1.

B. It uses broadcasts for its routing updates.

C. It is a classless routing protocol.

D. It has a lower default administrative distance than RIP version 1.

E. It supports authentication.

F. It does not send the subnet mask in updates.

Answer: ACE

48. What should be part of a comprehensive network security plan?

A. Allow users to develop their own approach to network security.

B. Physically secure network equipment from potential access by unauthorized individuals.

C. Encourage users to use personal information in their passwords to minimize the likelihood of passwords being forgotten.

D. Delay deployment of software patches and updates until their effect on end-user equipment is well known and widely reported.

E. Minimize network overhead by deactivating automatic antivirus client updates.

Answer: B

49. How should a router that is being used in a Frame Relay network be configured to avoid split horizon issues from preventing routing updates?

A. Configure a separate sub-interface for each PVC with a unique DLCI and subnet assigned to the sub-interface.

B. Configure each Frame Relay circuit as a point-to-point line to support multicast and broadcast traffic.

C. Configure many sub-interfaces on the same subnet.

D. Configure a single sub-interface to establish multiple PVC connections to multiple remote router interfaces.

Answer: A

50. What is the maximum data rate specified for IEEE 802.11b WLANs?

A. 10 Mbps

B. 11 Mbps

C. 54 Mbps

D. 100 Mbps

Answer: B

36. Host 1 is trying to communicate with Host 2. The e0 interface on Router C is down. Which of the following are true? (Choose two.)

A. Router C will use ICMP to inform Host 1 that Host 2 cannot be reached.

B. Router C will use ICMP to inform Router B that Host 2 cannot be reached.

C. Router C will use ICMP to inform Host 1, Router A, and Router B that Host 2 cannot be reached.

D. Router C will send a Destination Unreachable message type.

E. Router C will send a Router Selection message type.

F. Router C will send a Source Quench message type.

Answer: AD

37. Refer to the exhibit. Assuming that the router is configured with the default settings, what type of router interface is this?

A. Ethernet

B. FastEthernet

C. Gigabit Ethernet

D. asynchronous serial

E. synchronous serial

Answer: B

38. On point-to-point networks, OSPF hello packets are addressed to which address?

A. 127.0.0.1

B. 172.16.0.1

C. 192.168.0.5

D. 223.0.0.1

E. 224.0.0.5

F. 254.255.255.255

Answer: E

39. While troubleshooting a connectivity problem, a network administrator notices that a port status LED on a Cisco Catalyst series switch is alternating green and amber. Which condition could this indicate?

A. The port is experiencing errors.

B. The port is administratively disabled.

C. The port is blocked by spanning tree.

D. The port has an active link with normal traffic activity.

Answer: A

40. Refer to the exhibit. The network shown in the exhibit is running the RIPv2 routing protocol. The network has converged, and the routers in this network are functioning properly. The FastEthernet0/0 interface on R1 goes down. In which two ways will the routers in this network respond to this change? (Choose two.)

A. All routers will reference their topology database to determine if any backup routes to the 192.168.1.0 network are known.

B. Routers R2 and R3 mark the route as inaccessible and will not accept any further routing updates from R1 until their hold-down timers expire.

C. Because of the split-horizon rule, router R2 will be prevented from sending erroneous information to R1 about connectivity to the 192.168.1.0 network.

D. When router R2 learns from R1 that the link to the 192.168.1.0 network has been lost, R2 will respond by sending a route back to R1 with an infinite metric to the 192.168.1.0 network.

E. R1 will send LSAs to R2 and R3 informing them of this change, and then all routers will send periodic updates at an increased rate until the network again converges.

Answer: CD

31. Which two values are used by Spanning Tree Protocol to elect a root bridge? (Choose two.)

A. amount of RAM

B. bridge priority

C. IOS version

D. IP address

E. MAC address

F. speed of the links

Answer: BE

32. Refer to the exhibit. The two exhibited devices are the only Cisco devices on the network. The serial network between the two devices has a mask of 255.255.255.252. Given the output that is shown, what three statements are true of these devices? (Choose three.)

A. The Manchester serial address is 10.1.1.1.

B. The Manchester serial address is 10.1.1.2.

C. The London router is a Cisco 2610.

D. The Manchester router is a Cisco 2610.

E. The CDP information was received on port Serial0/0 of the Manchester router.

F. The CDP information was sent by port Serial0/0 of the London router.

Answer: ACE

33. While troubleshooting a network connectivity problem, a technician observes steady link lights on both the workstation NIC and the switch port to which the workstation is connected. However, when the ping command is issued from the workstation, the output message “Request timed out.” is displayed. At which layer of the OSI model does the problem most likely exist?

A. the session layer

B. the protocol layer

C. the data link layer

D. the access layer

E. the network layer

F. the application layer

Answer: E

34. A network administrator has configured two switches, named London and Madrid, to use VTP. However, the switches are not sharing VTP messages. Given the command output shown in the graphic, why are these switches not sharing VTP messages?

A. The VTP version is not correctly configured.

B. The VTP operating mode is not correctly configured.

C. The VTP domain name is not correctly configured.

D. VTP pruning mode is disabled.

E. VTP V2 mode is disabled.

F. VTP traps generation is disabled.

Answer: C

35. In order to allow the establishment of a Telnet session with a router, which set of commands must be configured?

A. router(config)# line console 0

router(config-line)# enable password cisco

B. router(config)# line console 0

router(config-line)# enable secret cisco

router(config-line)# login

C. router(config)# line console 0

router(config-line)# password cisco

router(config-line)# login

D. router(config)# line vty 0

router(config-line)# enable password cisco

E. router(config)# line vty 0

router(config-line)# enable secret cisco

router(config-line)# login

F. router(config)# line vty 0

router(config-line)# password cisco

router(config-line)# login

Answer: F